PharmaLectures.com

Courses › Pharma training by role › Production and engineering: everything Europe expects of you, in one course

Production and engineering: everything Europe expects of you, in one course

Your engineers meet the next inspection with complete files and the line still running.

  • 10 audio modulesthree lengths each
  • 1 h 40 min to 8 h 20 minbriefing to expanded
  • Workbook, transcript, certificateand a recorded quiz per module
  • Production and engineeringwho it is written for

Why this training matters

A Good Manufacturing Practice (GMP) inspector asks for the qualification file of a filling line, and the Operational Qualification report is not where it should be. Engineers search shared drives while batch release waits. The finding widens the inspection into other areas.

What changes after this course

Your engineers build the European requirements into designs, protocols and maintenance plans before the auditor arrives. You hold a certificate for each learner and a training record per person, ready to hand over when asked.

Watch the pitch

3:43 on how an audio course is bought, listened to and recorded. Full screen, one click.

Watch the pitch3:43, full screen, one click

What this course gives your people

A contractor proposes a new room layout and you decide on the spot whether it holds up under EudraLex Volume 4, Chapter 3. Your engineers treat premises and equipment requirements as design limits, not a checklist applied afterwards. When an inspector asks about your contamination control strategy under Annex 1, the answer is a document your team wrote and can point to.

Qualification stops being a scramble before release. Your validation engineers write Annex 15 protocols with acceptance criteria that Quality Assurance can approve on the first read, and they know when a parameter shift is a note and when it is a deviation. Requalification intervals come with a reason attached.

Upgrades to automated systems no longer stall on a data integrity question. Your team applies Annex 11 to controllers, sensors and logbooks, and checks audit trails and access rights before the system goes live, not after the inspector asks who changed a set point.

Change control requests leave engineering complete. Each one carries an ICH Q9 risk assessment, a clear reason and a root cause where a deviation started it. Quality Assurance stops sending them back, and every calibration and maintenance task traces directly to product quality.

Who needs this training

  • Production Engineer

    Asked for a qualification file during a walk-through, they produce the right Annex 15 report in minutes, because they know what each document must contain and where it belongs.

  • Quality Assurance Reviewer

    Change requests land on their desk without a risk assessment. They get a clear way to judge an ICH Q9 assessment in minutes and to tell engineering exactly what is missing.

  • Facilities Manager

    An inspector questions the utility maintenance schedule. They leave knowing how to set water, compressed gas and calibration plans that match what European inspectors expect to see.

  • Validation Engineer

    A legacy automated system has no clear audit trail and Annex 11 is the question. They get practical steps to secure electronic records on older equipment and to defend those steps to an auditor.

Roles: Production and engineering

Businesses: every kind of pharma company

Countries: India, China, Türkiye, Korea, Japan, Taiwan, Egypt, Gulf and MENA, Brazil and Latin America, Pakistan, Bangladesh and Vietnam, United States, Europe

Selling into: Europe and the UK

Courses are in English. Other languages on request.

After this course your people can

  1. Write a validation master plan that follows EudraLex Volume 4 and Annex 15 and lists what each qualification stage must prove.
  2. Build a preventive maintenance and calibration schedule based on failure history that cuts unplanned downtime.
  3. Check an automated engineering system against Annex 11 and close gaps in access control and audit trails.
  4. Draft a change control request with a risk assessment that Quality Assurance can approve without returning it.
  5. Map contamination risks in your facility and match each one to an Annex 1 control.
  6. Run an ICH Q9 risk assessment on a new line and record the mitigation steps an inspector expects.
  7. Prepare the first documents an inspector asks for before the opening meeting.

What the company gets

  • Engineering changes reach approval faster, because Quality Assurance receives complete requests with a risk assessment attached.
  • Validation and qualification files are complete and easy to find, so an inspector's first request gets an answer at the table.
  • Automated systems are checked against Annex 11 by people trained to do it, which closes data integrity gaps before an audit finds them.
  • Each engineer has a certificate and a training record, so you can show an auditor who completed each module and its questionnaire.

The evidence: questionnaire, training record, certificate

EU GMP Chapter 2, section 2.11, and 21 CFR 211.25 both ask for training that is documented and shown to work. This is what each learner leaves behind.

A recorded questionnaire per module

Every one of the 10 modules ends with a multiple-choice questionnaire. The result is recorded per person with a timestamp, whichever of the three lengths the person listened to.

A per-person training record

The export lists each learner, each module, the result and the date, which is the training record EU GMP Chapter 2 and 21 CFR 211.25 ask you to keep and the first thing an inspector asks for.

A certificate per learner

Name, company, course, hours, the guideline version taught and the date. It documents in-company training; it is not a professional qualification or an accreditation.

Your pass mark, your rule

There is no fixed pass mark. Your quality or human-resources manager decides what counts as passed and when a module is retaken, exactly as your training procedure says.

Delivered within 72 hours of payment, with the workbook, the full transcript and a source for every fact in the audio.

How long it takes, by who is listening

Nobody spends a day in a classroom. Every module exists in three lengths; a person takes the length their role needs, and every length ends with the same recorded questionnaire, so the training record is complete either way.

Briefing1 h 40 min10 min a module, for executives, sales and anyone who must know the rules, not run them
Standard4 h 10 min25 min a module, for regulatory, quality and business-development staff
Expanded8 h 20 min50 min a module, for technical staff who run the procedure day to day
Who takes this courseLengthTotal time
Production and engineeringStandard4 h 10 min

Course outline: 10 modules

10 modules. Under each title are the three things the listener can do afterwards; the audio itself runs 10 to 50 minutes depending on the length chosen.

  1. 1Design facilities that meet EudraLex Volume 4 manufacturing rules

    • How to read a floor plan the way an inspector does, and fix the flaws before the walk-through.
    • The Chapter 3 premises checks that show an inspector your layout prevents cross-contamination.
    • What to put in the facility file so a question about flows gets answered in one document.
  2. 2Run equipment qualification cycles that satisfy Annex 15

    • Why Operational Qualification protocols come back from review, and the acceptance criteria that stop it.
    • How to set requalification intervals you can defend with data instead of habit.
    • When a parameter drift is a note in the record and when it is a failed qualification.
  3. 3Schedule calibration and maintenance that prevents unplanned downtime

    • How to build a preventive maintenance plan from failure history, so the line stops only when you choose.
    • What to do when a critical sensor is found out of calibration in the middle of a batch.
    • The calibration record layout that proves to an inspector the work was done on time.
  4. 4Supply pharmaceutical water and clean gases that pass their tests

    • How to design a water for injections loop that holds up against the European Pharmacopoeia.
    • The dead legs in piping where biofilm starts, and how to spot them on a drawing.
    • When to sample compressed air and nitrogen for particles and microbes, and where.
  5. 5Stop microbial contamination with Annex 1 facility controls

    • How to draw personnel and material flows that keep microbes out of the cleanroom.
    • Why a contamination control strategy under Annex 1 must be one living document, not a folder of procedures.
    • What to check in your gowning procedure against the revised Annex 1 before an inspector does.
  6. 6Secure automated engineering systems against Annex 11 breaches

    • How to lock down electronic records on machine controllers so Annex 11 questions have clean answers.
    • The data integrity trap hiding in a newly installed sensor, and the check that closes it.
    • What attributable, legible, contemporaneous, original and accurate records look like in a logbook.
  7. 7Write change control requests that Quality Assurance approves fast

    • How to write an equipment modification request that Quality Assurance can sign without a phone call.
    • The root cause method that stops the same mechanical deviation from coming back.
    • When replacing a part needs full change control and when a like-for-like entry is enough.
  8. 8Rank engineering project risks with International Council for Harmonisation Q9

    • How to run an ICH Q9 risk assessment before the new line is installed, not after the first deviation.
    • The mitigation steps that satisfy an inspector when you find a risk in your facility.
    • Why rating every engineering risk as critical weakens your case, and how to rank them instead.
  9. 9Answer the exact questions inspectors ask about engineering

    • The validation reports an inspector asks for first, ready on the table before they ask.
    • How to answer a technical question in two sentences without opening a second line of inquiry.
    • What to prepare before the opening meeting so engineering is never caught off guard.
  10. 10Fix audit findings for good with targeted preventive actions

    • How to turn an audit observation into a fix that removes the cause, not just the symptom.
    • The indicators that show your equipment is in a state of control, ready to show an auditor.
    • Why small maintenance delays turn into major deviations, and where to cut that chain.
The founders

One of us was inspected. The other one pays for the training.

Every claim below is sourced on the about page: the medicines register, the Lithuanian Pharmaceutical Union board list, the university directory.

Justina Krukonytė-Racz

Justina Krukonytė-Racz

Co-founder. Licensed pharmacist.

GDPResponsible PersonWarehouse & logistics

Licensed pharmacist. Responsible Person at Tamro (PHOENIX group), where she led the GDP set-up of the distribution centre.

The Responsible Person is the named person the regulator holds accountable for every pallet that leaves the building.

She writes the modules around the procedures a GDP inspection checks. Board member of Lithuanian Pharmaceutical Union.

Listed in the Lithuanian medicines register as Pharmacist.

Prof. Ben Racz

Prof. Ben Racz

Co-founder. Builds the platform and is responsible for delivery, records and pricing.

Platform & deliveryQuantitative researchCarnegie Mellon

He was Professor of the Practice at the College of Engineering at Carnegie Mellon University, where he taught Advanced Quantitative Finance and Algorithmic Trading to MSc students.

He is the founder and Managing Director of Algorithmic Sciences, a scientific research and consulting firm. Earlier he co-founded a data-driven growth consultancy, a data-science based wholesale trading company and an information security firm.

More about Ben at benracz.com

Questions about this course

Is there a certificate?

Yes. Every learner who finishes the course receives a certificate in their own name, and every module ends with a recorded multiple-choice questionnaire, so the certificate sits on top of a per-person training record. The certificate documents in-company training; it is not a professional qualification or an accreditation, and your quality or human-resources manager sets the pass mark and decides when a module is retaken.

How long does the course take?

10 modules, each in three lengths: a 10-minute briefing, a 25-minute standard run and a 50-minute expanded walk-through. The whole course takes 1 h 40 min in the briefing length and 8 h 20 min in the expanded length. People take the length their role needs, and every length ends with the same recorded questionnaire, so the training record is complete either way.

Who should take this course?

It is written for Production and engineering. Owners, managers and sales staff hear the briefing length, regulatory, quality and business-development staff take the standard run, and the people who run the procedure every day get the expanded version. One licence covers one named person on this course for a year, so the same title can be rolled out across a whole team at once.

Is this training accepted as a GMP training record by an auditor?

EU GMP Chapter 2 and 21 CFR 211.25 require documented, effective training, and that is what the course produces: a recorded multiple-choice result per module and per person, a certificate per learner and a transcript of what was taught. No provider can promise acceptance by a specific inspector; the record is built to answer what inspectors ask for, and your quality manager decides the pass mark.

How is it delivered and how fast?

The course arrives as audio files with a companion workbook, a full transcript and the questionnaire per module, within 72 hours of your payment arriving. You host the files on your own system or share them as you like; there is no platform to log into and no learner management system to set up. The free sample module arrives on request, before any purchase.

What does it cost per learner?

The list price is 9 euros per module, per learner, per year, so this course is 90 euros for one person for twelve months. The price per learner falls as more people take the same course: 10 learners pay 10 percent less and the discount keeps growing to 50 percent at 1000 learners. Type a number on the price panel and the yearly total appears.

Get this course for your team

One licence is one person on this course for a year. All three lengths, the workbook, the certificate and the training record are included in every purchase. Pick how many people, add it to the cart, and you have an invoice in your inbox.

Free sample module

Hear one full module before you spend a cent. Send your company and the role you want trained, and a complete sample module comes back with its workbook and transcript.

Connect on WhatsApp

or email [email protected], or ask for a written quote for your team