PharmaLectures.com

Courses › GMP, GDP, quality and compliance › Proving the process: process validation, cleaning validation and continued process verification

Proving the process: process validation, cleaning validation and continued process verification

Your team answers the validation inspector from the file, and the audit moves on.

Process validation is the documented evidence that a manufacturing process, run within its set parameters, consistently makes product that meets its specifications. The United States Food and Drug Administration guidance of 2011 describes it in three stages, process design, process qualification and continued process verification, and Annex 15 of the EU GMP guide, revised in 2015, follows the same life cycle under the name ongoing process verification. Cleaning validation is the matching proof that equipment is clean enough between products, now set against health-based exposure limits in Europe.

  • 12 audio modulesthree lengths each
  • 2 h to 10 hbriefing to expanded
  • Workbook, transcript, certificateand a recorded quiz per module
  • Production, QA, engineeringwho it is written for

Why process validation training matters

An inspector from the U.S. Food and Drug Administration asks for the cleaning validation report on your shared line. Nobody can say why the worst-case product was chosen or how the swab limit was set. The question runs into the afternoon, and the batch waiting on that line stays on hold.

What changes after this course

Your engineers write protocols whose acceptance criteria already answer the inspector, and your team spots process drift before a batch is at risk. You hold a certificate for each learner and a training record for each person.

Watch the pitch

3:43 on how an audio course is bought, listened to and recorded. Full screen, one click.

Watch the pitch3:43, full screen, one click

Process validation training: what this course gives your people

Your engineers stop waiting for a consultant to say what the U.S. Food and Drug Administration expects from process validation. They write protocols that follow the three stages of the 2011 guidance and the validation master plan that Annex 15 describes. Acceptance criteria are set before the first batch, so nobody rewrites a protocol after the data arrives.

Production supervisors use International Council for Harmonisation Q8 and Q9 to decide which parameters matter and which risks need a control. A change on the floor gets a quick answer: does it touch a critical quality attribute or not. Installation, Operational and Performance Qualification reports then arrive complete the first time, with calibration and utilities already checked.

Quality Assurance specialists build cleaning validation around the European Medicines Agency guideline on health-based exposure limits and Annex 15. They name the worst-case product, convert the limit into a swab or rinse limit, and prove recovery on the real surface. A held batch caused by a missing recovery study stops happening.

After launch, the team runs Continued Process Verification, the third stage of the 2011 guidance, and reads Shewhart control charts before a trend turns into a failed batch. Quality system monitoring under International Council for Harmonisation Q10 fits the same data. When the inspector asks about periodic review, your people open the schedule and the reports.

Who needs process validation training

  • Production Supervisor

    A process change reaches the floor and someone asks whether it needs revalidation. You check it against the Performance Qualification data and the critical parameters, and give a clear answer the same shift.

  • Quality Assurance Specialist

    An inspector from the U.S. Food and Drug Administration asks why one product was chosen as worst case. You open the cleaning validation report and point to the toxicology, the solubility and the limit.

  • Validation Engineer

    You draft the Operational Qualification protocol for a new mixer. Test ranges and action levels are set to the worst case, so the first run is a real test and the protocol does not need reissuing.

  • Process Development Scientist

    You prepare to scale a new product. Your critical process parameters and design space notes arrive at technology transfer in a form the validation team can turn straight into a protocol.

  • Quality Control Analyst

    You own the method that measures residue on a swab. Recovery, detection limit and sample handling are settled before the study starts, so the cleaning results are not thrown out.

Roles: Quality assurance and Qualified Person, Production and engineering

Businesses: every kind of pharma company

Countries: India, China, Türkiye, Korea, Japan, Taiwan, Egypt, Gulf and MENA, Brazil and Latin America, Pakistan, Bangladesh and Vietnam, United States, Europe

Selling into: any jurisdiction

Courses are in English. Other languages on request.

After this course your people can

  1. Place the three stages of the 2011 U.S. Food and Drug Administration process validation guidance in your own site's documents.
  2. Write a process validation protocol with acceptance criteria and a reasoned number of batches.
  3. Complete Installation Qualification with every critical utility and calibration record checked before testing starts.
  4. Set Operational Qualification test ranges and action levels that challenge equipment at its worst case.
  5. Calculate a residue limit from a health-based exposure limit and choose swab or rinse sampling for each surface.
  6. Plot a Shewhart control chart from commercial batch data and flag a drift signal.
  7. Build a periodic review schedule that covers every validated process and cleaning procedure on site.

What the company gets

  • Cleaning validation reports state the worst-case choice and the limit, so an inspector's first question has an answer on the page.
  • Validation master plans follow Annex 15 of European Union Good Manufacturing Practice from the first draft, so fewer pages come back for rework.
  • Process data from commercial batches is reviewed on a set schedule, so drift reaches Quality Assurance before it reaches a release decision.
  • Fewer protocols are reissued and fewer cleaning studies are repeated, which frees engineering time for the next project.
  • Every learner has a certificate and a training record entry, so the training file is ready when an inspector asks who was trained.

The evidence: questionnaire, training record, certificate

EU GMP Chapter 2, section 2.11, and 21 CFR 211.25 both ask for training that is documented and shown to work. This is what each learner leaves behind.

A recorded questionnaire per module

Every one of the 12 modules ends with a multiple-choice questionnaire. The result is recorded per person with a timestamp, whichever of the three lengths the person listened to.

A per-person training record

The export lists each learner, each module, the result and the date, which is the training record EU GMP Chapter 2 and 21 CFR 211.25 ask you to keep and the first thing an inspector asks for.

A certificate per learner

Name, company, course, hours, the guideline version taught and the date. It documents in-company training; it is not a professional qualification or an accreditation.

Your pass mark, your rule

There is no fixed pass mark. Your quality or human-resources manager decides what counts as passed and when a module is retaken, exactly as your training procedure says.

Delivered within 72 hours of payment, with the workbook, the full transcript and a source for every fact in the audio.

How long it takes, by who is listening

Nobody spends a day in a classroom. Every module exists in three lengths; a person takes the length their role needs, and every length ends with the same recorded questionnaire, so the training record is complete either way.

Briefing2 h10 min a module, for executives, sales and anyone who must know the rules, not run them
Standard5 h25 min a module, for regulatory, quality and business-development staff
Expanded10 h50 min a module, for technical staff who run the procedure day to day
Who takes this courseLengthTotal time
Quality assurance and Qualified PersonExpanded10 h
Production and engineeringExpanded10 h

Process validation course outline: 12 modules

12 modules. Under each title are the three things the listener can do afterwards; the audio itself runs 10 to 50 minutes depending on the length chosen.

  1. 1Map the validation lifecycle across international guidelines

    • How to show where each stage of the 2011 U.S. process validation guidance sits in your files.
    • What Annex 15 of European Union Good Manufacturing Practice expects to see in your validation master plan.
    • When one validation file can serve both a U.S. inspector and a European one, and when it cannot.
  2. 2Write process validation plans that hold up under inspection

    • What a process validation protocol states up front so nobody rewrites it after the first batch.
    • How to set acceptance criteria that your Quality Assurance head will defend in front of an inspector.
    • Why the number of batches in your plan needs a written reason, not just the habit of three.
  3. 3Design manufacturing processes that are built to validate themselves

    • How to use International Council for Harmonisation Q8 to tie quality attributes to process parameters.
    • The step where a Quality Risk Management finding becomes a control you can test in the next batch.
    • When a process design report is complete enough to move to qualification, and when it is not.
  4. 4Execute Installation Qualification against the manufacturer's specifications

    • The utility and instrument checks that stop an installation sign-off from bouncing back to you.
    • Why a calibration certificate that expires mid-test puts the whole Installation Qualification in doubt.
    • How to check the delivered equipment against the purchase order and drawings before anyone signs.
  5. 5Run Operational Qualification that tests your equipment at its limits

    • How to choose the test range so a worst-case run shows where the equipment really stops working.
    • Why an action level that operators can read at the panel gets followed, and a vague one does not.
    • What to do when a standard operating procedure fails during Operational Qualification.
  6. 6Conduct Performance Qualification that supports commercial batches

    • How to size a Performance Qualification batch so it represents the commercial scale you will run.
    • The sampling points that show a batch is uniform, not just that it passed release.
    • Why a Performance Qualification report should say what each deviation did to the result.
  7. 7Build a cleaning validation strategy that regulators accept

    • How to turn a health-based exposure limit into a residue limit for the next product in the train.
    • The way to pick the worst-case product on shared equipment and explain the choice in one paragraph.
    • Why European Union Good Manufacturing Practice Chapter 5 treats cross-contamination as a design question.
  8. 8Carry out cleaning validation studies with exact sampling methods

    • How to choose between swab and rinse sampling for each surface, and how to defend the choice.
    • How to prove your recovery percentage on the real surface material before the first study run.
    • The analytical method flaw that makes a clean piece of equipment look dirty on paper.
  9. 9Keep cleaning validation valid through every change

    • When a change to a product, a cleaning agent or a part needs revalidation, and when a note will do.
    • How to wire change control so nobody edits a cleaning procedure without a review.
    • What belongs in the cleaning validation report so the inspector stops after the first read.
  10. 10Plan Continued Process Verification for commercial runs

    • How to choose which parameters and attributes to monitor, and write down the reason for each.
    • The sampling frequency that fits a stable process and the one that fits a young process.
    • Why a data plan written before launch saves you rebuilding history from batch records later.
  11. 11Analyze Continued Process Verification data to catch drift early

    • How to read a Shewhart control chart so a run of points on one side of the line gets noticed.
    • What to do when a result passes specification but sits outside the trend.
    • How to turn a drift signal into a corrective action with an owner and a date.
  12. 12Manage your validation program so it stays audit-ready

    • How to set a periodic review that tells you which validated process is due, before an inspector does.
    • The filing order that lets you hand over any validation report while the inspector is still in the room.
    • What to do after a Form 483 observation names a validation gap, from the first day to the reply.
The founders

One of us was inspected. The other one pays for the training.

Every claim below is sourced on the about page: the medicines register, the Lithuanian Pharmaceutical Union board list, the university directory.

Justina Krukonytė-Racz

Justina Krukonytė-Racz

Co-founder. Licensed pharmacist.

GDPResponsible PersonWarehouse & logistics

Licensed pharmacist. Responsible Person at Tamro (PHOENIX group), where she led the GDP set-up of the distribution centre.

The Responsible Person is the named person the regulator holds accountable for every pallet that leaves the building.

She writes the modules around the procedures a GDP inspection checks. Board member of Lithuanian Pharmaceutical Union.

Listed in the Lithuanian medicines register as Pharmacist.

Prof. Ben Racz

Prof. Ben Racz

Co-founder. Builds the platform and is responsible for delivery, records and pricing.

Platform & deliveryQuantitative researchCarnegie Mellon

He was Professor of the Practice at the College of Engineering at Carnegie Mellon University, where he taught Advanced Quantitative Finance and Algorithmic Trading to MSc students.

He is the founder and Managing Director of Algorithmic Sciences, a scientific research and consulting firm. Earlier he co-founded a data-driven growth consultancy, a data-science based wholesale trading company and an information security firm.

More about Ben at benracz.com

Questions about process validation training

What are the three stages of process validation?

Stage one, process design, defines the process from development and scale-up knowledge and identifies the parameters that matter. Stage two, process qualification, confirms that the facility, utilities and equipment are qualified and then runs the process at commercial scale to show it is reproducible. Stage three, continued process verification, keeps collecting and analysing data during routine production so drift is seen before it becomes a failure.

What is continued process verification?

It is the ongoing stage after the initial validation runs: trending critical process parameters and quality attributes from every commercial batch, using statistical tools to detect shifts, and feeding the results into product quality reviews, change control and CAPA. EU GMP Annex 15 calls it ongoing process verification and expects a documented protocol stating what is monitored, how often and what triggers action. Three good batches once is no longer enough.

Is there a certificate?

Yes. Every learner who finishes the course receives a certificate in their own name, and every module ends with a recorded multiple-choice questionnaire, so the certificate sits on top of a per-person training record. The certificate documents in-company training; it is not a professional qualification or an accreditation, and your quality or human-resources manager sets the pass mark and decides when a module is retaken.

How long does the course take?

12 modules, each in three lengths: a 10-minute briefing, a 25-minute standard run and a 50-minute expanded walk-through. The whole course takes 2 h in the briefing length and 10 h in the expanded length. People take the length their role needs, and every length ends with the same recorded questionnaire, so the training record is complete either way.

Who should take this course?

It is written for Production, QA, engineering. Owners, managers and sales staff hear the briefing length, regulatory, quality and business-development staff take the standard run, and the people who run the procedure every day get the expanded version. One licence covers one named person on this course for a year, so the same title can be rolled out across a whole team at once.

Is this training accepted as a GMP training record by an auditor?

EU GMP Chapter 2 and 21 CFR 211.25 require documented, effective training, and that is what the course produces: a recorded multiple-choice result per module and per person, a certificate per learner and a transcript of what was taught. No provider can promise acceptance by a specific inspector; the record is built to answer what inspectors ask for, and your quality manager decides the pass mark.

How is it delivered and how fast?

The course arrives as audio files with a companion workbook, a full transcript and the questionnaire per module, within 72 hours of your payment arriving. You host the files on your own system or share them as you like; there is no platform to log into and no learner management system to set up. The free sample module arrives on request, before any purchase.

What does it cost per learner?

The list price is 9 euros per module, per learner, per year, so this course is 108 euros for one person for twelve months. The price per learner falls as more people take the same course: 10 learners pay 10 percent less and the discount keeps growing to 50 percent at 1000 learners. Type a number on the price panel and the yearly total appears.

Get this course for your team

One licence is one person on this course for a year. All three lengths, the workbook, the certificate and the training record are included in every purchase. Pick how many people, add it to the cart, and you have an invoice in your inbox.

Free sample module

Hear one full module before you spend a cent. Send your company and the role you want trained, and a complete sample module comes back with its workbook and transcript.

Connect on WhatsApp

or email [email protected], or ask for a written quote for your team